Which direction do you coil cable?

Dear Swami,
I'm working on a show with some electricians who insist that feeder cable should be coiled in a clockwise direction, but I think it depends on the cable. What's the proper direction to coil cable?
Signed,
Coiling in Columbia

Dear Coiling,

Does the sun rise to your right or to your left? Like the direction of the sun, the direction to coil cable depends on which way you are looking at it. To get it right every time, follow the natural coil of the cable. If it wants to coil clockwise, coil it clockwise. If it wants to coil counter-clockwise but you want to coil it clockwise, then flip it over and coil it clockwise. Either way, the sun will shine upon you.

Signed
Swami Candela of the Third Millennium

Comments

  1. PipMay 23, 2016 at 11:03 AM

    I agree that it's easier to coil cable whichever direction it wants to coil. But if a cable wants to coil counter-clockwise, no matter which direction you flip the coil, it will always look counter-clockwise. The only way to get a cable that wants to coil counter-clockwise to coil clockwise is to continuously twist the cable to get the twist of the cable going in the opposite direction.

    ReplyDelete
  2. PipMay 23, 2016 at 11:03 AM

    I agree that it's easier to coil cable whichever direction it wants to coil. But if a cable wants to coil counter-clockwise, no matter which direction you flip the coil, it will always look counter-clockwise. The only way to get a cable that wants to coil counter-clockwise to coil clockwise is to continuously twist the cable to get the twist of the cable going in the opposite direction.

    ReplyDelete

Post a Comment

Popular posts from this blog

Amps Are All Askew

Dear Swami, I'm stumped (and so is everyone I've asked thus far). I can't seem to figure out the power draw on a show. Here's the layout: 15 - VL4k spots @ 208V; 16,000W each = 24,000W 3 - Clay Paky Alpha 800 @ 208V;  1200VA each =  3600W (assuming PF = 1) 12 - S4 Series 2 Lustr @ 208V; 168W each =  2016W 3 - Colorado Solo1 @ 208V; 62W each =  186W So that's: 24,000   3,600   2,016      186 29,802W total   The incoming voltage from the service is about 117V phase-to-neutral and about 202V phase-to-phase. When I do the math (29,802W ÷ 202V), I keep coming up with 147.5A total, or 49 amps per leg in a balanced 3-phase system. What my meter is telling me is about 82 to 86 amps with every light in the rig on full. Unfortunately, audio and video are using the same service, so that pushes it up to the low 90s range, and it's a 100-amp service, so it is way too close. Am I missing so...
Read more

Segregating DMX

Image
Dear Swami, I've heard people say that you should separate fixture types on their own DMX line or they will not work properly. Is that true? Signed, Lines Crossed in Dimmer Land Dear Crossed, The sky is dotted with clouds that color truth. DMX is well defined and as long as the maker of the machine follows the path of the protocol it will take flight. There is no technical reason for segregating DMX fixtures by type, although there may be historical reasons. In the early days of automated lighting, Martin used an non-compliant pinout and swapped pins 2 and 3. If you used an adaptor it would work with any other DMX devices. Old habits are like the weeds that grow between the cracks in the sidewalk. To be rid of them is hard. There may be other reasons for the practice of segregating DMX by fixture type but it has nothing to do with compliant fixtures.
Read more